Call (000) 000-0000

Frequently Asked Questions

How do I reset my GE washer?

Unplug the washer (or switch off the breaker) for 1–2 minutes, plug it back in and start a short cycle. Top-load GE models with a lid lock may need the lid opened and closed once. If a code returns right away, the fault is real — call for diagnosis.

How do I reset my GE dishwasher?

Press Start/Reset (or Cancel) and wait ~2 minutes while it drains, or turn the breaker off for 1 minute. A delay-start number with "H" (e.g. 2H) is not an error.

How do I unlock my GE dishwasher?

Most GE dishwashers lock the controls by holding the Lock (or Heated Dry on some models) button for 3 seconds; hold it again for 3 seconds to unlock.

How do I reset my GE refrigerator?

Unplug or switch off the breaker for 1–2 minutes. On dispenser models you can also clear codes with System Check. If the fridge shows dE (defrost) or FF repeatedly, it needs service.

How do I reset the ice maker on a GE refrigerator?

Turn the ice maker off for ~15 seconds, press the water dispenser paddle 3 times during that time, then turn it back on. It should cycle within a few minutes.

What does H2O mean on a GE dishwasher?

Low or no water. Check that the shut-off valve under the sink is fully open and the supply line isn't kinked. If it continues, the inlet valve or flow meter needs testing.

What does FTD mean on a GE dishwasher?

Failure to drain. Clean the filter, check the drain hose and air gap; on a new install remove the disposer knockout plug. If it still won't drain, the drain pump is the usual cause.

What does F2 mean on a GE oven?

The oven overheated or the temperature sensor circuit reads too hot. Turn the breaker off and have a technician check the sensor and control relays — don't keep using it.

What does "Tank Low" mean on a GE washer?

It's a SmartDispense reminder, not a fault: refill the detergent tank (about 8–10 loads left).

What is error 353 on a GE Profile washer/dryer combo?

GE says the lint filter is most likely clogged (often by fabric-softener residue). Separate the foam filter from the mesh, rinse and brush both, then run a wash & dry cycle.

What does tF / tC (or "EF") mean on a GE refrigerator?

Not errors: TurboFreeze and TurboCool are switched on.

How old is my GE appliance?

Read the first two letters of the serial number: the 1st is the month, the 2nd is the year (repeats every 12 years). Example: "DA…" = February 2025. See our serial decoder.

How long do GE refrigerators / dishwashers last?

Typically 10–15 years for refrigerators and about 9–12 years for dishwashers with normal maintenance. Repair usually makes sense if the cost is under ~50% of a new unit and the appliance is younger than ~8–10 years.

Do you repair GE Profile, Café and Monogram?

Yes — all GE Appliances brands, including Hotpoint.

Are you GE authorized / factory service?

No — GE's own factory service is Bodewell. We are a local Charlotte-area repair company that services GE Appliances products, uses OEM parts where available and stands behind every repair with our own labor warranty.

Is my GE appliance still under warranty?

GE's standard limited warranty is typically 1 year parts & labor (longer on some sealed systems/components). If it's under warranty, contact GE first; we're happy to help after that.

How much does GE appliance repair cost in Charlotte?

Our service call / diagnostic fee is $89 and it is applied to the repair when you approve it. You get a written price before any work starts.

How do I remove the agitator from a GE washer?

Pull off the agitator cap/fabric-softener dispenser, remove the bolt underneath (usually 7/16" or 1/2"), then lift the agitator straight up. Unplug first.

How do I clean the filter on a GE dishwasher?

Twist out the cylindrical fine filter at the bottom of the tub, lift the coarse filter, rinse under warm water with a soft brush, reinstall until it locks.

GE appliance down?

Same-day service across the Charlotte area · Open 7 days · 7:00 AM – 10:00 PM

📞 Call now