GE Washer Error Codes
What GE washer error codes mean and what a technician checks for each one. Need it fixed? GE washer repair in Charlotte.
Top-load GTW / HTW (2015+ digital display; 27")
| Code | Meaning | What to check |
|---|---|---|
| 1 | Basket spins with lid unlocked | Check lid lock/switch wiring; reconnect or replace harness; if wiring OK replace lid lock/switch. |
| 2 | Lid lock/switch failure | Check lid lock/switch wiring, repair harness, then replace lid lock/switch. |
| 3 | Locked motor | Remove overload; turn basket by hand. Binding = stuck item or spin bearing. If free: motor harness, start capacitor, motor. |
| 4 | Control reset its software (info) | No fault - appears on power-up or leaving diagnostics. |
| 5 / 10 | Mode shifter failure | Check harness board-to-shifter; shifter approx. 5,700 ohms; replace if open or ~0. |
| 6 | Water overflow | Tub fills while unplugged = inlet valve. Otherwise check pressure air hose, then control board. |
| 8 | Water level pressure sensor failure | No fill: faucets open, valve screens, hoses, valve wiring. Fills: air hose, then control board. |
| 9 | Lid switch error (lid not opened for 3 cycles) | Open lid after cycles; if persists check wiring/replace lid lock. |
| 11 | AC power not 60 Hz | Power supply problem - check with utility. |
| 12 / 20 / 21 | Water overflow | Air hose, then control board; tub fills unplugged = inlet valve. |
| 13 / 14 / 23 / 24 | Lid lock/switch failure | Check wiring; replace lid lock/switch. |
| 15 | Thermistor (water temperature sensor) failure | Check thermistor connector; replace thermistor. |
| 16 / 18 | Not draining | Drain clog, hose kinks, pump harness; replace pump if it does not run. |
| 17 | Basket won't spin at start of wash | Do not load wet clothes; drain tub; check for stuck item. |
| 19 | Paused >24 h or water in tub while off | Restart within 24 h; tub fills while off = leaking inlet valve. |
| 22 | Can't balance dry load | Redistribute; rotate basket by hand; motor-to-board harness. |
| 25 | Water level drops when not draining | Drain hose siphoning, air hose, tub leak. |
| 26 / 31 | Out of balance in final spin | Redistribute load, level the washer (4 legs), check binding/harness. |
| 27 | Lid open >15 min with water in tub | Restart within 15 min; air hose; control board. |
| 29 | Excessive suds | Let suds dissipate; use correct amount of HE detergent. |
| 30 | Stuck key on control panel | UI-to-board harness, user interface, then control board. |
| 32 | Can't unlock lid | Check wiring; replace lid lock/switch. |
Top-load CleanSpeak / newer GTW (hex codes)
| Code | Meaning | What to check |
|---|---|---|
| 01 | UI control board defective | Unplug 5 min; if returns replace UI board. |
| 05 / 06 / 76 / 77 | Bulk detergent / softener dispenser malfunction | Hose clogs/kinks, tank level sensor wiring, replace sensors. |
| 07 | Stuck button on UI board | Unplug 5 min; replace UI board. |
| 08 / 68 | Water level pressure sensor defective | Sensor wiring, air hose to tub, pressure sensor, main board. |
| 09 / 65 / 66 / 0E | Lid lock defective | Harness lid lock to main board; replace lid lock. |
| 0A / 10 | Not filling with water | Both supply valves open, frozen lines, siphoning, inlet valve. |
| 0B | Drain pump defective | Clear drain/hose clogs; replace pump. |
| 0D / 12 / 72 / C9-CF / D5 / DD-DF | Main control board defective | Unplug 5 min; if returns replace main board. |
| 11 | Heater defective | Heater wiring, heating element, main board. |
| 16 / 17 / 18 | Mode shifter defective | Shifter wiring, shifter, main board. |
| 19 | Flood level detected | Not overfilling = pressure switch; overfilling unplugged = inlet valve. |
| 6A / 6B | Water temperature thermistor defective | Wiring; thermistor approx. 13,840 ohms at 70°F. |
| D2 | Locked rotor on drive motor | Basket spins freely? Motor/hall sensor wiring, hall sensor, main board. |
| D3 | Hall (motor speed) sensor defective | Wiring, hall sensor, main board. |
Front-load GFW (27")
| Code | Meaning | What to check |
|---|---|---|
| 1 | Basket spins with door unlocked | Door lock wiring; replace door lock/switch. |
| 2 / 62 | Door lock failure | Harness, then door lock/switch. |
| 3 | Locked motor | Reduce load, drain; turn basket by hand; motor/tach wiring; drive motor. |
| 6 / 20 | Water overflow | Tub fills unplugged = inlet valve; air hose; control board. |
| 8 | Water level pressure sensor failure | Faucets, valve screens, hoses, valve wiring, air hose, board. |
| 9 | Door switch error | Open door after cycles; wiring; door lock/switch. |
| 15 | Thermistor failure | Connector; thermistor. |
| 17 | Basket won't spin at start | Dry clothes only; check binding - spin bearing. |
| 18 | Not draining | Drain clog, hose kinks, pump harness, drain pump. |
| 19 | Paused >24 h or water in tub while off | Restart within 24 h; leaking inlet valve. |
| 22 | Can't balance dry load | Redistribute; binding = spin bearing; motor harness. |
| 23 / 24 | Door won't lock | Wiring; door lock/switch. |
| 25 / 65 | Water level drops when not draining | Siphoning drain hose, air hose, tub leak. |
| 26 / 31 | Out of balance in final spin | Redistribute; level legs; spin bearing; motor harness. |
| 27 | Door open >15 min with water | Restart; air hose; control board. |
| 29 | Excessive suds | Let suds settle; correct HE detergent dose. |
| 30 | Stuck key | Harness, UI, control board. |
| 32 / 77 | Can't unlock door | Wiring; door lock/switch. |
| 33-34, 41-51, 66-74, 83 | Drive motor or inverter board failure | Wait 45 min for motor TCO; wiring board-inverter-motor; motor windings; inverter. |
| 35 / 59 / 60 / 61 / 63 / 64 | Accelerometer board failure | Harness accelerometer-to-board; replace accelerometer board. |
| 37 | Heater failure | Thermistor 12-15 kOhm, heater ~15 ohm at room temp. |
| 38 / 39 / 40 / 84 | Vent damper failure | Damper harness; vent damper. |
| 57 | Door unlocked with water above door threshold | Drain; refills unplugged = inlet valve; else control board. |
| 58 | Electronic control board failure | Replace control board. |
Front-load GFWS / WCVH (older E-codes)
| Code | Meaning | What to check |
|---|---|---|
| E22 | Fill timeout (>8 min) | Supply valves, inlet hoses & screens, water valve, water level sensor. |
| E23 | Flood protect / slow drain | Drain pump, restrictions, drain height. |
| E31 | Drain timeout | Drain pump, restriction; drain height over 96 in. |
| E38 | Dispenser error | Dispenser motor/switches. |
| E39 | Dispenser timeout | Dispenser motor/switches. |
| E42 | Drive motor over-current | Unplug 30 s; motor windings; inverter. |